Clicky

Civil Engineering

Structure of Road| Types of Road And Technical Terms of Road

Structure of Road | Types of Road |Technical Terms of Road

Structure of Road| Types of Road And Technical Terms of Road

Today I have the topic of Structure of Road and Types of Road And Technical Terms of Road. Structure of Road | Types of Road |Technical Terms of Road. This article all details the road with all parts in technical language. Structure of Road| Types of Road And Technical Terms of Road I hope in this article you will get all the basic and details information about the road.

Structure of Road| Types of Road And Technical Terms of Road

Learn More

  1. Estimate The Concrete Volume For The Staircase 

  2. Highways Engineering Interview MCQ’S

  3. How To Calculate The Estimate of Building Construction

STRUCTURE OF ROAD

Crossing the road vertically shows different parts of the road mentioned below

1- Subgrade

2- Sub Base

3- Base

4-Surfacing

Subgrade

This is the surface of the ground, on which the road is built. Its surface is usually kept 60 cm (2 feet) above ground level so that rainwater does not reach the road surface. If the road needs to be built in the cutting section, the subgrade is below ground level. The strength of the road depends largely on that part.

Sub Base

This part is not an integral part of the road but when the subgrade is weak, an additional layer of gravel or some other suitable material is provided to strengthen the road. Which is called sub-base.

Base

This is an integral part of the road. It bears the weight of the traffic moving on the road and safely transfers to the sub base or subgrade. The strength of the road depends on that part. This part of the road is usually made of solid gravel.

Surfacing

This is the upper part of the road which makes the road surface smooth. It also makes the road surface impervious. The type of road is determined by this section. This section protects the lower part of the road.

TYPES OF ROADS

Roads are basically divided into two Groups

1. Earthen Roar’s

2. Pucca Roads

Earthen Roads

These types of roads are usually built in rural areas. The local soil of the area is used to build these roads. For a good road, the ratio of clay to sand should be 65:35. If the condition of the land is not good, then stabilization is done before building the road.

In this process, the ratio of clay to sand is corrected. Or cement, bitumen or other chemicals are added to the soil. The road is then built from this soil.

PuccaRoads

Pucca roads are good. The country’s major cities and towns are connected by these roads. There are two more types of paved roads.

i) Bituminous Roads

Sub-base and base layers are laid after the preparation of sub-grade to make this type of road. Sub-base layer is made of a layer of bricks or gravel or any suitable material, while the base layer is made of stone and gravel. A layer of priming coat is laid on top of the base layer. It consists of a mixture of bitumen and kerosene. Bitumen is spread over it as a tack coat and the last layer is surfaced on top of it. That consists of Stone Metal and bitumen. If the surface treatment consists of two layers, it is called Double Surface Treatment (DST). For better roads, three layers id called Triple Surface Treatment (TST).

ii) Concrete Roads

Cement is used in the construction of these types of roads. These roads are long-lasting and do not require much attention to repair, but the construction of these roads is costly, so mostly these roads are not built in Pakistan. These roads are also called rigid roads.

TECHNICAL TERMS OF ROADS

1-Land Width

The total width of a road owned by it is called Land Width. It is also called the Right of Way.

2. Formation Width

The width of the road at the prepared surface of the road is called formation width. This includes the paved part and the width of the shoulder.

3. Metalled Width

The paved part of the road on which high-speed traffic flows is called the Metalled Width. It is also called the carriageway.

4- Shoulder 

The surface left on the side of the paved part of the road is called the shoulder. This part of the road is used to repair a vehicle malfunction or in case of another emergency. This is also called Berm.

5- Side Slopes

Slopes are provided on the sides of the road from the level of formation to the ground level so that the road is safe. This slope is called the side slope.

6- Gradient

The slope along the length of the road is called the gradient. If this gradient is towards the upside then it is called the Upward gradient and if it is the downside then it is called a downward gradient.

7- Separator

Lines drawn to divide a road into two or more sections along its length are called separators. It is sometimes made of concrete or masonry. If it is used to separate different types of traffic, it is called a Grade Separator.

8- Footpath

A path parallel to the side of the road that is made for walking is called a footpath. Its wia is 1.3 meters (4 feet).

9- Bicycle Track:

The path made for cyclists towards the side of the road is called Bicycle Track. It is kept 2 meters 6 (f) wide.

10- Kerb

An obstacle that separates a paved road and a sidewalk is called a kerb. It is usually made of concrete blocks or stone.

11- Camber

The slope facing the width of the road is called camber. The purpose is to remove rainwater from the surface of the road.

12- Crete Way

In low-lying roads, the road is sometimes paved just under the wheels of vehicles. Such roads are called the Crete Way.

13- Urban Road

A road built in an urban area is called an urban road. In addition to the paved section of this road, sidewalks and separators are also made.

14- Country Road

A road built outside the urban population is called a country road. Footpaths are not usually built on their sides.

15- Service Road

A is made parallel to the main road, which is connected to the main road at some distance. The purpose of this road

16- Water Bound Macadam Roads

This is a paved road that does not Ch-05 use any binding material such as bitumen and cement. After preparing the sub-grade in the preparation of this road, the sub-base and the base layer e made of gravel. It is regularly compacted and an adequate amount of water is used during compaction. Due to the fact that this road is called are Water Bound Macadam (W.B.M) Road, Bituminous Roads or Concrete Roads can be constructed on it.

17- Resurfacing

The prepared surface of the road is called surfacing. If this surface is damaged and it is called resurfacing if a layer of the same material is applied to repair it.

18- Double Surface Treatment

If two layers of bitumen and gravel are provided to the upper surface of the road, it is called Double Surface Treatment (D.S.T)

19- Triple (T.S.T) Surfacing

If three layers of bitumen and gravel are applied to the upper surface of the new road or to repair the road, they are called Triple Surface Treatment (T.S.T).

20- Overlay

To repair a road if the additional base material is put on top of the old road and three layers of surfacing are applied to it, it is called an overlay.

21-Raising

If the old road is uprooted and filled with soil and the road is rebuilt on it, it is called rising.

22- Arboriculture

Plantation along the roadside is called arboriculture.

Read  More

  1. What Is Culvert Different Shapes of Culverts And Types of Culverts With Full Detail

  2. Elements of The Road Carriage Way Details

  3. How To Calculate The Quantity of Road Asphalt

Thanks for Reading Article Get more Information and share it with others.

JOIN US & LIKE MY OFFICIAL FACEBOOK PAGE 

Raja Numan

Hi, My name is Engr. Raja Numan author of Engineering Information Hub and I am a Civil Engineer by Profession and I've specialized in the field of Quantity Surveying, Land Surveying as QC Engineer in national and multinational companies of Pakistan & Saudi Arabia.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button
error: Content is protected !!